CNC cutting & robotic welding systems · Jinan, China · Since 2006info@laser-solution.com

Heavy pipe · CNC plasma cutting and beveling

CNC Large pipe cutting machine

Large Diameter Pipe Cutting Machine, Ø600-2000 mm

6-axis CNC plasma for heavy-wall steel pipe up to 10 tonnes

A CNC plasma pipe cutter built for pipe that standard machines cannot hold. A 3-jaw self-centring chuck turns pipe from Ø600 to Ø2000 mm while the cutting unit follows the pipe surface automatically and cuts end bevels, branch holes, saddles and intersections, with V, X and K bevels in one pass.

  • Free test cut on your pipe
  • 3-year machine warranty
  • Installed in 80+ countries
  • Factory direct since 2006
Large diameter steel pipe cutting machine for pipe 600-2000 mm
Pipe diameter
Ø600-2000 mm
Pipe weight
up to 10 t
Plasma
200-400 A
Clamping
3-jaw self-centring
Wall thickness
plasma ~50 mm, oxy-fuel 6-200 mm

What is a large diameter pipe cutting machine?

A large diameter pipe cutting machine, also called a large pipe cutting machine or big pipe cutting machine, rotates a heavy round steel pipe while a CNC plasma torch cuts its profile. It is built for the top end of the pipe range, Ø600 to Ø2000 mm and up to 10 t, where a standard pipe cutting and beveling machine runs out of chuck size and a tube laser runs out of wall thickness. One program cuts the pipe to length, the weld bevel, any branch holes and the saddle on the branch pipe that fits them.

Why heavy pipe needs a different machine

Problem with Ø600-2000 mm pipeHow this machine handles it
Large pipes are hard to centre and a 10-tonne pipe sagsThe 3-jaw self-centring chuck centres the pipe automatically when it clamps, and supports under the pipe carry the weight
The surface moves up and down as the pipe rotates because it is not perfectly roundThe whole cutting unit rises and falls automatically to keep the torch at the right height
Ovality and bow put the torch off the surfaceActive trajectory compensation corrects the cutting path to the real pipe shape
Fumes fill the inside of a large pipeInternal extraction draws the fumes out through the pipe
Walls of 20-50 mm need weld preparation3D V, X and K bevels cut in the same pass as the profile

Large diameter pipe cutter specifications

SpecificationDetails
Pipe diameterØ600-2000 mm
Max. pipe weightup to 10 t
Clamping3-jaw self-centring chuck
Height controlcutting unit rises and falls automatically with the pipe surface
Process6-axis CNC plasma cutting and beveling
Wall thicknessup to about 50 mm carbon steel with plasma
Oxy-fuel (flame) cutting systemoptional, carbon steel 6-200 mm
Plasma power200-400 A, chosen to the wall thickness
Bevel typesV, X and K, 3D bevel up to ±45°
Path correctionactive trajectory compensation for ovality and bow
Fume controlinternal extraction through the pipe
Pipe lengthbuilt to order

Pipe length, plasma source and torch carriage are configured to your pipe. Send the largest pipe size, wall thickness and length and we confirm the configuration in the quotation.

Cutting thickness: plasma and oxy-fuel

Typical production piercing thickness on carbon steel. The exact value depends on the plasma source and gas.

Cutting systemCarbon steel wall
200 Aabout 25-30 mm
300 Aabout 40 mm
400 Aabout 50 mm
Oxy-fuel system (option)6-200 mm

Plasma, laser or oxy-fuel for large pipe?

ProcessBest for
Plasma (this machine)Ø600-2000 mm, walls up to about 50 mm, fast cutting and beveling
Oxy-fuel (option on this machine)Carbon steel walls 6-200 mm, beyond plasma range; slower
Tube laserThin-wall pipe and tube under about Ø600 mm

Get the price and a free test cut

The price depends on the largest diameter, pipe weight and length. Send those, or a drawing, and we reply with a configuration and quotation. We can also cut a sample on your pipe and send the video.

Get a quote WhatsApp

Joints on heavy pipe

On Ø600-2000 mm pipe the joints are the same as on smaller pipe, but every cut is larger, heavier and harder to correct by hand, so cutting the right shape and bevel first time matters more. Typical jobs on this machine:

PartWhat the machine cuts
Offshore jacket legs and bracesBrace ends shaped to the leg, with a bevel that changes around the joint
Line pipe and fittingsSquare or bevelled ends, tees and laterals
Penstock sectionsBranch outlets and bevelled ends
Pressure vessel and tank shellsNozzle openings, bevelled for the nozzle weld
Tube truss chordsHoles and slots where braces and gussets join

Cut types the machine makes

Straight cut with bevel on large diameter pipe
Straight cut with bevel
Miter cut on large diameter pipe
Miter cut
Hole for branch on large diameter pipe
Hole for branch
Saddle cut on large diameter pipe
Saddle cut
Double saddle on large diameter pipe
Double saddle
Saddle-miter on large diameter pipe
Saddle-miter
Lateral branch on large diameter pipe
Lateral branch
Through holes on large diameter pipe
Through holes
Slots on large diameter pipe
Slots
Reinforcing pad on large diameter pipe
Reinforcing pad
Transition cut on large diameter pipe
Transition cut
Custom openings on large diameter pipe
Custom openings

For the full list of cut types and how branch bevels work, see pipe profile cutting: 12 types of cuts explained.

How a large pipe is cut, step by step

  1. Load: the crane lowers the pipe onto the supports and the 3-jaw chuck clamps and centres it.
  2. Program: enter the pipe size, wall thickness and joint type, or import the 3D model; the software generates the cutting path and bevel angles.
  3. Measure: the machine checks the real pipe surface and corrects the path for ovality and bow.
  4. Cut: the chuck rotates the pipe while the torch moves along it, cutting profile and bevel together; fumes are drawn out through the pipe.
  5. Unload: the finished pipe comes off ready for fit-up and welding, with no grinding or manual bevelling.

Large-diameter pipe cutting applications

Use the rotary pipe cutter to make end bevels, branch openings and intersecting joints on large steel pipe.

Offshore and marine

Jacket legs and braces, piles and node joints with intersecting branches.

Pipelines and fittings

End bevels, tees and laterals on large line pipe.

Hydropower penstocks

Large pipe sections with bevels and branch outlets.

Pressure vessels and tanks

Nozzle holes in shells, cut and bevelled ready for welding.

Large tube trusses

Chords and braces for stadiums, airports and bridges.

Heavy machinery

Large cylinders and structural tubes with complex cut-outs.

Cut samples

Steel pipe with cut openings, beveled ends and intersecting joints
Cut openings, end bevels and intersecting joints
Plasma-cut steel pipe rings arranged in a row
Plasma-cut pipe rings

Large diameter pipe cutting video

Large diameter pipe cutting and beveling

Is this the right machine for your pipe?

Your pipeRecommended machine
Ø600-2000 mm, heavy wall, up to 10 tThis large diameter pipe cutting machine
Ø40-600 mm, round and square, with bevels5-axis pipe plasma cutting machine
Ø600-2000 mm with walls over about 50 mmThis machine with the oxy-fuel cutting system (6-200 mm)
Ø40-600 mm with very thick wallsPlasma and oxy-fuel pipe bevel cutter

See all models on the CNC pipe cutting and beveling machine page.

Before you order: what to check

CheckWhy it matters
Largest and smallest pipeSets the chuck size and the lifting stroke of the cutting unit
Heaviest pipeSets the chuck and support capacity (up to 10 t on this model)
Thickest wallSets the plasma current; above about 50 mm, add the oxy-fuel cutting system (6-200 mm)
Longest pipeSets the bed length and crane access
Joint typesPlain bevels only, or branches and saddles in 3D
Floor space and powerThe bed, supports and fume extraction need room on both sides

Why buy from PCL

  • Factory direct

    Discuss your pipe and joint requirements with the team that builds the machine in Jinan.

  • Free test cut

    Send a representative joint so you can review the cut and bevel before ordering.

  • Installation and training

    On-site installation includes operator training.

  • Remote support

    Get help with operation and troubleshooting over WhatsApp or video.

CNC pipe cutting and beveling machine

CNC Pipe Cutting and Beveling Machine

Overview of all pipe cutting and beveling models.

Compare models
5-axis CNC tube plasma cutting machine

5-Axis Pipe Plasma Cutter

Round and square pipe up to Ø600 mm.

View
CNC plasma and oxy-fuel pipe bevel cutter

Plasma and Oxy-Fuel Pipe Bevel Cutter

Thick-wall pipe Ø40-600 mm, oxy-fuel to 200 mm.

View
8-axis pipe and beam plasma cutting machine

8-Axis Pipe and Beam Plasma Cutter

Pipe, box, channel and H-beam on one machine.

View

Frequently asked questions

What is a large diameter pipe cutting machine?

A CNC machine that rotates a large steel pipe while a plasma torch on a moving carriage cuts its profile: end bevels, branch holes, saddles and intersections. This model handles pipe from Ø600 to Ø2000 mm and up to 10 t, which is beyond the range of standard pipe cutters and tube lasers.

How do you handle pipes up to 2000 mm?

A heavy-duty 3-jaw self-centring chuck clamps, centres and rotates the pipe while supports under the pipe carry its weight. As the pipe turns, the whole cutting unit rises and falls automatically to follow the real pipe surface, so the torch stays at the right height even on a pipe that is not perfectly round.

Is internal extraction necessary?

Yes, for this size. A Ø2000 mm pipe is a large closed space; without extraction, plasma fumes collect inside and block the operator’s view and the sensors. The machine draws the fumes out through the pipe during cutting.

What wall thickness can it cut?

It depends on the plasma source fitted. As a guide for carbon steel, a 200 A source pierces up to about 25-30 mm, a 300 A source about 40 mm and a 400 A source about 50 mm in production. For heavier walls, an optional oxy-fuel (flame) cutting system cuts carbon steel from 6 to 200 mm. Tell us your thickest wall and we size the source to it.

Which bevels can it cut?

V, X and K bevels in 3D, with the bevel angle changing around the pipe as needed for saddles and branch connections. The torch tilts up to ±45°, which covers standard weld preparations such as 30°-37.5° V bevels with a root face.

What does trajectory compensation do?

Large pipes are never perfectly round or straight. The machine measures the real surface and corrects the torch path for ovality and bow, so the cut and the bevel stay where they should be along the whole pipe.

Can it cut intersections and saddles for branch pipes?

Yes. Enter the main and branch pipe sizes and the angle, or import the model, and the software generates the intersection curve and the matching saddle on the branch, with the bevel angle varying around the joint.

Why plasma and not laser for this size?

At Ø600-2000 mm and walls of 20-50 mm, plasma is the practical process: it cuts thick carbon steel quickly at a much lower machine cost than a laser of the same size, and it bevels in the same pass. Tube lasers are better for thin-wall pipe under about Ø600 mm.

What industries use it?

Offshore jackets and piles, pipelines and fittings, hydropower penstocks, pressure vessels and tank nozzles, and large tube trusses for stadiums, bridges and airports.

Can I see a test cut on my pipe?

Yes. Send a drawing or the pipe size, wall thickness and joint type, and we cut a sample at our factory in Jinan and send photos or a video.

How long does it take to cut one joint?

It depends on the pipe size, wall thickness and joint type. A plain bevel on a large pipe end takes minutes; a branch intersection with a varying bevel takes longer. Send your typical joint and we estimate the cycle time from a test cut.

What maintenance does it need?

Daily: check and replace plasma consumables and clean the torch. Weekly: clean the chuck jaws and supports and check the lifting axis of the cutting unit. Monthly: lubricate guides and check the extraction filters. Consumable life depends on current and arc-on time.

What is the warranty?

Three years on the machine. Consumables such as nozzles and electrodes are excluded.

Is this the same as a standard pipe cutting and beveling machine?

It is the heavy end of the range. For pipe from Ø40 to 600 mm, a standard 5- or 6-axis pipe cutting and beveling machine is faster and cheaper; this model is built for pipe that is too big or too heavy for those machines.

Get a quote and a test cut

Tell us the outside diameter, wall thickness, length, and weight of your largest pipe. Include the steel grade and the joint or bevel you need to cut.

What happens next

  1. An engineer checks your sizes and recommends a machine configuration.
  2. We send a quotation based on your pipe and cutting requirements.
  3. For a test cut, send a drawing on WhatsApp. We can cut a sample and share the video.
WhatsApp +86 186 6017 4681

Request a quote

Your details are used only to answer this enquiry. Or email info@laser-solution.com.

WhatsApp